A Ford Transit L3 H3 fitted out for a m​​ulti-utility company

A complete racking system in a multi-utility company’s Ford Transit

The Ford Transit in these photos is an L3 H3 model. This means there is plenty of room in the cargo compartment and excellent opportunities for installing Syncro System racking. Syncro racking solutions are always fully customised. In this case the customer is a multi-utility service company who plans to use the van to maintain the local network of water pipes. Let’s take a closer look!

Syncro aluminium floor liners are tough and washable

Proper bodywork protection is essential to extend the life of your van and save you unnecessary expense for repairs. This Ford Transit L3 H3 is fitted with a complete set of liners comprising:

  • a floor liner in aluminium tread plate, often the best choice when a van is going to be exposed to dirt and damp as it is easy to clean and boasts an excellent non-slip surface;
  • liners for the walls and tops of the doors in strong steel panelling;
  • specially shaped, marble-look plywood liners for the bulkhead, plus a practical, lockable over-cab storage compartment that is easily accessible from the cargo compartment and extends under the cab roof.

Syncro boasts the largest selection of van bodywork protection on the market, with over 30,000 articles in the catalogue, so you can choose whatever combination suits your needs and the use you make of your van!

Syncro shelves, drawers and enclosed compartments on the left of the van

The entire left side of this multi-utility company’s Transit is taken up by storage. Two floor-level areas provide practical enclosed compartments. Above these are eight configurable shelves extending almost to the roof. Finally, we have four metal drawers with non-slip mats and internal dividers and a full-length top tray with a fold-down door at the back and easy access from above to place and remove long objects.

The Ford Transit’s work area

On the right of the Transit alongside the sliding door, Syncro System has installed a complete work area. The structure that supports the work surface consists of a floor-level compartment around the wheel arch and two columns or racking above, one with two small but practical shelves and the other with three metal drawers. The work surface is made from plywood covered with a sheet of stainless steel for maximum resistance to impacts and stress during operations. The bench is equipped with a metal vice. Serving the work bench is a wall-mounted tool rack panel that can hold small tools where they are instantly visible and accessible, keeping them securely in place when the van is travelling.

A customised bulkhead for the multi-utility company

The Transit’s bulkhead is protected by custom-made, marble-look plywood panelling and equipped with the cargo retaining accessories requested by the customer: two sections of exclusive and amazingly versatile Syncroblock slider bar, arranged in parallel. Syncroblock bar is compatible with a large number of Syncro accessories and can be used in many different ways depending on the needs of the job in hand. In this Transit, the top bar is equipped with three hooks for clothes, a cable holder and a movable, telescopic hook. The bottom bar features a combination of hooks and straps to hold loads of various shapes and sizes in place.

Accessories to complete the Transit’s transformation

In addition to the cargo retaining accessories described above, which are installed on the bulkhead, this Transit is also equipped as follows:

  • Left rear door: a handwash kit with a water tank and tap and a liquid soap dispenser, both with dedicated holders;
  • Right rear door: two lengths of Syncroblock bar with four Prax hooks;
  • Side panel of left racking: a bar rack with lashing strap, a length of slider bar with hooks for clothes, and a paper roll holder;
  • Side panel of right racking: Syncroblock bar with more garment hooks;
  • Top of right wall: a paper roll holder;
  • Forward facing side panel of right racking: Syncroblock bar with hooks and a strap;
  • Roof cross members: LED lights.

Syncro can transform any van into a perfect mobile workshop: call us!

There’s no such thing as a van that cannot be transformed thanks to the expertise of Syncro and the incredible versatility with which Syncro racking elements can be combined. Ask your nearest Syncro dealer to arrange an obligation-free consultation. Don’t delay! Transform your van now and enjoy immediate advantages in your work!

Syncro System has transformed tens of thousands of vans since 1996, and all solutions have been fully personalised for each customer.


SEND YOUR REQUEST!!!



OUR CUSTOMER SERVICE TEAM WILL CONTACT YOU AS QUICKLY AS POSSIBLE.

CONTACT US FOR
A FREE OFFER